Parts

Fits: REVIVE/REVIVE 2.0, REVIVE MAX, and DIVINE Includes: - x1, Cable clamp body (# 52) - x1, M4 Set screw (# 7)

Valve-extension-adapter. Allows easier access to your dropper valve for shock-pumps with short valve heads.

This BikeYoke allows the use of a standard shock in your Specialized bike. Stumpjumper 2010-2015 Includes: - 1x BikeYoke SJ01 - 1x DU bushing - 1x reducer - 1x stainless steel bolt

- Perforated leather handlebar tape - Genuine perforated leather - Kit includes: 2 strips of light, perforated leather bar tape, 2 rubber bar end plugs and 2 adhesive cloth strips - Self Adhesive: Yes - Tape Length: 215mm

The Burgtec composite pedal is everything you'd expect from a Burgtec pedal but at a more affordable price point. Uncompromised grip, rugged durability, the exact same sculpted simple lines, fully backed up with spares and at an affordable price. The best of both worlds can exist. - Nylon and Fibreglass Body - SCM415 Cromo Axle - All replaceable steel pins - 16mm Profile, 1mm Dish - 96mm x 102mm Platform - Weight: 376g

Bigger, grippier, lighter and as tough as ever. The Penthouse Flat MK5 pedal is here! After two years of development and testing the MK5 Penthouse Flat is here. Retaining our signature toughness, the MK5 is the lightest and grippiest Burgtec pedal to date. We did this by not only increasing the size of the pedal platform but also how concave it is. Furthermore, we reduced the diameter of the pins and added the most wear-resistant internals on the market. From the outside to the inside, we've sweated the details of the MK5 to bring you the ultimate flat pedal. - Weight: 379g - Platform material: 7075 Alloy - Profile: 15mm - Platform: 100mm x 102mm - Dish: 2mm (concave) - Pin material: Stainless steel - Pin width: 3.5mm - Pin height: 4.5mm - Axle Material: EN24T Steel - Internals: 2 x Igus W300 bushings, single sealed bearing and inboard rubber oil seal

Clean and Simple is always best. Leverless design for added security and clearance for when situations get tight. These super tough axles tighten up with a 6mm Allen key. Dropout Bolt is also provided. Constructed from 7075 Aluminium and made to the manufacturer's exact specifications. Fits the following Santa Cruz bikes: - 5010 V1, V2, V3 - Bronson V1, V2, V3 - Nomad V2.1, V3, V4 - Chameleon V5, V6, V7 - Heckler V7 - Heckler E-Bike V8 - Heckler MX E-Bike - Bantam V1 - Blur TR V1.1 - Blur XC V2.2 - Blur LT V2.2, V2.1c - Blur V3 - Highball V1, V2, V3 - Tallboy LT V1.1 - Tallboy V1.1, V2, V3, V4 (MY20 & MY21 only) - High Tower V1 and V2(MY20 & MY21 only) - High Tower LT V1 - Mega Tower V1 - And Juliana Equivalents Exact Axle Length is 168.5mm x Thread M12 x 1.0mm pitch also fits other brands that use this size.

The Ride Wide Alloy Enduro Handlebars are the original and best wide bar. It's the little differences that make it one of the most comfortable bars in its class. The backsweep and upsweep help the bar to the ultimate feel once tried always loved. As used by the Santa Cruz Syndicate riders Greg Minnaar, Jackson Goldstone, Nina Hoffman, and Laurie Greenland. - 800mm width - 9 degree backsweep - 5 degree upsweep - Suggested cut down marks - Weight: 300g

Unmatched comfort and unquestionably superior vibration dampening properties. The Burgtec Ride Wide Carbon Enduro Handlebars is built to take a beating. - Uni-Directional Carbon - 800mm width - 35mm bar clamp - 20mm or 30mm rise - 9 degree backsweep - 5 degree upsweep - Weight: 258g

When you've got to finish your bike off right. The Burgtec Stem Spacers are the perfect finishing kit.

"Make a grip with the fussiest rider on the planet, you must be mad!!" The Bartender Pro is the next level in grip design for Burgtec. We've collaborated with 3x World Champion Greg Minnaar to hone the construction of this grip to produce unrivaled vibration dampening. - 31.5mm Diameter. - 30A Rubber Compound - Single Lock On

The Goats Grip just went Super Soft. Prototyped through the 2020 season and based on the World Cup Winning pattern of the Bartender Pro as used by Greg, as well as Nina Hoffman, Danny Hart and Angel Suarez. - Super Soft Compound - 31.5mm Diameter - Single Lock-on - Tapered Core

- LEV has always represented the latest technology but is already a classic among top contending dropper posts. - With myriad of firsts to its name; first hydraulic dropper to offer zero cable movement, first dropper to win a UCI World XC Eliminator event and first in countless enduros, magazine tests and customer satisfaction polls, LEV IS the first dropper seatpost to outperform itself.

- Eten-I rounds out the lower end of the KS internally routed dropper post spectrum with a post that is perfect for new riders just getting used to the idea of on-the-fly seat height adjustment or more experienced riders looking for a value-priced solution. - Eten-I uses the same head and cartridge as the Eten Remote but moves the cable interface to the bottom of the post for compatibility with frames accommodating internally routed cables.

PEMBREE DBN is an entirely new seat post clamp. Due to the double barrel nuts DBN provides a consistent clamping force ensuring the bolt remains straight through-out its travel. This is particularly important when clamping dropper posts to prevent pitch points that damage frames and posts. Machined to exacting standards ensures a precision fit that is critical to secure clamping. DBN seat post clamp is manufactured from aluminium that is 75% recycled, unheard of in the industry. Machined from stainless steel the precision, custom made bolt provides the core clamping function of DBN. - Clamp: Aluminium - Bolt: Stainless Steel TX25 - Barrel Nuts: Aluminium - Weight: 27g - Warranty: 5 Years

The first saddle designed specifically for the eBike, combining the advantages of 3D Skingel technology with a functional design to guarantee greater comfort, safety and control.

- Lightweight Design - Steel rings with engineering polymer spacers - Nickel finish - 8 Speed compatible - Weight—346g

- 11 speed wide range cassette - 7075 Aluminum largest sprocket - Alloy spiders, spacers and lockring - Fits Shimano/SRAM freehub - 465g (11-46); 401g (11-42); 389g (11-40)

- Steel cogs - Composite spacers

These bearing cups are suited for installation of the THM Clavicula on frames with bottom bracket housings to BB30 standard applicable to axles with 30 mm diameter. The bottom bracket housing is 68 mm wide and its inner diameter is 42 mm. The snap rings wich for the BB30 standard are used as limit stop when pressing in the bearings, must not be installed. The relatively small bearing clearance of 68 mm could lead to considerable axle deformations. Our solution with bearings at the outside involves a reduced load on the axle which can be seen from the higher rigidity. Another advantage is the facility of using the same crank for frames to BB30 standard and those with BSA or Italian thread. The increase in weight of the complete system is neglegible. Increase in weight: Road 12 g only

The “Clavicula DH” is the downhill version of our superlight racing crankset. Designed with additional reinforcements it is intended for the extreme demands of downhill racing: Even flying debris, crashes on rocky terrain or sliding along the ground can hardly hurt this crank. Thanks to intelligent design it is still light as a feather. The low weight of the “Clavicula DH” improves the overall handling of any DH bike. A lighter bike will always be more responsive to steering input and thus easier to control. At only 450 g for the complete crankset including the bottom bracket the “Clavicula DH” is much lighter than similar sets. Power transfer and longetivity satisfy the most demanding racer. The crank comes complete with a 38-tooth chainring and is shipped with bottom bracket and mounting tool.

Bar end plugs are vital for any bike. The new Wolf Tooth Alloy Bar End Plugs feature a machined 6061-T6 aluminum end cap, a bolt, and an expandable plastic nut to comprise a lightweight, secure bar end plug option. - Available in eight colors that match existing anodized Wolf Tooth headsets, seatpost clamps, chainring bolts, and more - It is compatible with drop bars and MTB bars.

Two-piece threaded cable tip contains the cable end without crushing it. CNC aluminum, no tools needed to install, reusable.

Parts for repair and maintenance of DT Swiss hubs. - DT Swiss 240s Shim Ring

Parts for repair and maintenance of DT Swiss hubs. - DT Swiss Shim Ring: for Star Ratchet Hubs with 26mm OD Driveside Bearings

RaceFace Crank Arm Fixing Bolts - M15

- Non-SIS 5mm alloy ferrules - Sold individually - Color: Silver

- Aheadset preload adjusting bolt

Replacement small parts for Hope disc brake Hope disc brake calipers.

Hope Brake Lever Parts

Internally fitting service parts for Hayes hydraulic disc brake master cylinders. - All HFX-MAG compatible master cylinder internals are designed for the current aluminum piston/2mm push-rod platform (2003 and newer).

Origin-8's 1 1/8-inch Headset Spacers are made of lightweight and durable aluminum and come in 2mm, 5mm or 10mm thicknesses and lots of cool colors to add style to your ride. You get a bag of 10 spacers.

- Brass barrel, 2.2mm cable pass-through, screwdriver slot on both ends

Shim spacers can be placed between bearing and compression cover in IS headsets to fine tune the fitment.

Service parts for Fox suspension.

Looking to get a little extra distance so that your derailleur clears your 40 or 42 tooth cog? Look no further. - M4 x 24mm screw for that extra little push

Bleed fittings specifically designed for Hayes hydraulic disc brakes.

- Allows quick chain removal without tools - MissingLink 410HD|~|1sp|~|BMX Heavy Duty chain|~|9.4mm|~|each|~| - MissingLink 410|~|1sp|~|BMX|~|8.6mm|~|each|~| - MissingLink II|~|8sp|~|all|~|7.1mm|~|6/card|~| - MissingLink-9|~|9sp|~|all|~|6.6mm|~|6/card|~| - MissingLink-10R|~|10sp|~|KMC, Shimano, SRAM|~|5.9mm|~|6/card|~| - MissingLink-10CR|~|10sp|~|Campagnolo only|~|5.9mm|~|6/card|~| - MissingLink-11|~|11sp|~|Campy, KMC, Shimano|~|5.5mm|~|6/card|~|

Sunlite's Cable End Button replaces the worn out piece that goes between your brake cable and the brake lever body. Replacing it along with cables and housing helps add new life to your brakes and shines u the bike, too!

Replacement piston and seals for Hope disc brake calipers.

KMC 3/16" Master Link Chain Links - For 3/16" chain, extra wide - Extra-wide, for non-derailleur bikes: BMX, cruisers, etc - Perfectly fits on KMC 415H & 415H-NP chains

- Half-link connector allows you to add or subtract half of one link (1/2 inch) from the chain in order to optimize chain tension - Uses standard chain pin connector and tool

KS Dropper Post Service Parts

Saddle clamp heads and lowers for KS Dropper posts.

Saddle clamp heads and lowers for KS Dropper posts.

- Model: Replacement bolt - Compatibility: Allen, M5x16

Hope Disc Brake Hose Small Parts · This washer fits on both sides of the banjo bolt and seals the hose fitting into the master cylinder

Replacement copper washers for 5mm or stainless Hope hydraulic brake line.

Replacement end plugs for the GA2, GA2 Fat, and GA3 grip models. - One size. - Sold as a pair. - Fits Ergon GA2, GA2 Fat and GA3 models only. - Designed to fit Trail / All-Mountain MTB handlebars on the market today.

Replacement right and left Ergon logo bar plugs. Features the Ergon logo in a vibrant white color. You have the choice of a plug set of the barend and non-barend models - Right and Left soft plastic bar plugs. - Sold as a set only. - Fits most handlebars. - Can be trimmed to fit various handlebar thicknesses. - Plug set for GP and GS grips with barends - fits GP2, GP3, GP4, GP5, GS2 and GS3 models only - Plug set for GP1, GC1 and GS1 grips - fits GP1, GC1, and GS1 only

HFX-Mag/-9, El Camino, Stroker Caliper-Hose Connection Seal

FSA Mega Exo Small Parts.

FSA Mega Exo Small Parts.

This is a replacement Brake Hose Cover for the Lever End of Shimano BH90-SBM, BH90-SB levers. - Covers brake hose fitting at the brake lever

- Replacement retaining clip for the Surly Tuggnut/Snuggnut

- Crank dust cap - Works with most three-piece crank models

Replacement bearing for the lower half of YST8003 #7 headset.

Replace the top bearing in your YST8300 headset with these caged ball bearings.

- Chrome - Sold individually

- Routes cables underneath the bottom bracket - Will not rust or corrode