Parts & Accessories

Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs. - End Cap Included

• Locking skewer set • Cro-Mo • 70g (set)

• Rim strips for 20-inch fat bike rims • 80mm wide

- Eady to install - Spoke mounted - 2 per set

- Supplies full wheel illumination for 700c/29in wheels and smaller - Approximately 40 hrs of battery life - Water resistant design - Includes 3 (AA) batteries - Sold individually (1 wheel) - Easy to install

- Shell: 8mm flanged axle nut - Flanged

- Type: Skewer only - Length: 220mm

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

- Flanged 15mm axle nuts - Durable chromoly construction - Spacing / Axle: B/O

Replacement cassette bodies for Origin8 RD-1200 series rear hubs - Supplier Part: QA1R - Use: Shi 11s - Bearing Type: Sealed - Compatibility: RD-1200

Replacement Cassette body for Origin8 hubs - Compatibility: #371359 / 370935 / 370936 / 391360 / 370930 / 370931 / 370979 - Use: 12s XD

Replacement Freehub body for OOZY Trail R142/135, SPIKE R135/142, or SPIKE DH R150/157 Rear hubs. Compatible with all OOZY hubs and wheels. Compatible only with SPIKE and SPOON wheels (135mm and 150mm) produced in 2016 or later (with SPIKE hubs).

- Replacement end caps for MT-4100 hubs

From Origin8 come these replacement hollow track axle sets for SS-1101 hubs.

- 6 pawl/54 point/6.6-degree engagement - Cassette bodies for Elite Series CX/GX/MT/FB-1110 hubs - Sealed bearings

- 10 x 135mm adapters for 6-Drive rear road disc hub - Includes: two adapters and one disc rotor spacer - Conversion kits for Spin Doctor 6-Drive hubs are not compatible with original Spin Doctor and Spin Doctor Pro hubs

- Replacement QR axles for Origin8 RD-1100 hubs

- Axle adapters for RD-1110 Elite Series front road disc hubs - Available in standard QR, 12mm, and 15mm thru-axle options

- End cap adapters for Origin8 RD1120 series 11-speed road hubs

- End cap adapters for Origin8 RD1120 series 11-speed road hubs

Origin-8's Torq Lite Track Cog Lock Ring 1.29" x 24 tpi with left-handed threaded thread is the only lock ring you need. Hardened threading and extra material make this highly durable to help you go the distance.

- High-quality fat bike rim strips - Super durable PVC material

You need rim tape to keep your tubes from blowing through the spoke holes, especially when landing big airs. WeThePeople's got your back, though. If your's is questionable, you better replace it with this WTP Nylon Rim Tape, a perfect fit with Logic Rims. - Strong - Lightweight - Tube-proof

Replacement Freehub Body for Trace hubs.

Stan's Threaded Valve Extenders let you convert deep-section rims to tubeless. They're precision-machined from aluminum and are designed to fit deep-dish carbon and aluminum rims. And, they're threaded on the outside so you can install the Presta lock-ring nut for a perfect seal.

WTP's Helix hub guards are designed to work on The Helixline of hubs, replacing the cones for a perfect fit without having to spread your dropouts. - Includes heat-treated chromoly adaptor to replace hub cone nuts for a perfect fit - Rear Hub guards are compatible with Helix V1 and Helix V2 freecoaster hubs and many other "KHE" style freecoasters on the market

Hub End Caps for Go-Devil Hubs. Caps for quick release, 12mm, and 15mm available.

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.

- Colored rim decal kits to personalize your ride - Decals to fit two (2) 70w 26-inch rims

Ultra-light, bolt-on thru-axles, with a low-profile 6mm head for use on Whisky forks and others. They are also available in some common rear frame sizes. See manufacturer's specifications for fitment questions. - Thread Length: 12mm

- Colored rim decal kits to personalize your ride - Decals to fit 2 100w 26-inch rims

- Colored rim decal kits to personalize your ride - Decals to fit two (2) 50w 27.5+ rims

Wheel Freehub Kit SS 176/177 SRAM XDR - End Caps Not Included Compatible With: WH-202-CCR-A1, WH-202-TLD-A1, WH-202-TUD-A1, WH-302-CCD-A1, WH-302-CCR-A1, WH-302-TLR-A1, WH-303-CCR-B1, WH-303-TLD-A1, WH-303-TUD-B1, WH-303-TUR-B1, WH-30C-CLD-A1, WH-30C-CLR-A1, WH-404-CCR-A1, WH-404-CCR-B1, WH-404-TLD-A1, WH-808-CCR-B1, WH-808-TLD-A1, WH-SP9-CC30-A1, WH-SP9-CCD-A1, WH-SP9-CCR-A1, WH-SP9-TUD-A1

Compatible with straight valve hole Hugo 52 rims and designed to fit 7.5 - 8.5mm valve holes. Sold as a pair. Identifying your Hugo rim and selecting the correct valve stem: Stepped Hugo rims have a larger diameter valve hole on the interior of the rim, and a narrower hole on outside of the rim. Quick tip: don't remove your tire if you don't have to. If your Hugo rim decal reads: MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this valve. For "Stepped" valve hole Hugo use part AS0105 - Valve Stem pair, Schrader, 32mm, 14mm base.

End caps for front conversion hubs.

The Deadbolt Thru-Axles feature the classic-looking Salsa lever and can be adjusted to return to the desired position when properly tightened. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications

The Deadbolt Ultralight Thru-Axles are offered in a 6mm flat button-head design, for a flush, clean look. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - One-piece design - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications - 6 mm hex wrench required for installation

- Longer skewers fit modern frames/forks with thicker dropouts - Aluminum lever/nut, Delrin pivot washer, serrated alloy nut with Nylock - White skewers are powder-coated - Shaft: chromoly - Wheel: front/rear - Spacing (front/rear): 100/135mm - Weight: 112g/set

Salsa's Ti Flip-Offs are as beautiful to the touch as they are to the eye. Lightweight. Smooth. Recommended for road use or rigid front mountain bike use only. Available in a whole host of colors. - Beautifully machined and hand-friendly - Black, Silver, Blue, Red, Green, Orange, Purple, or Pewter - More than just eye candy, they’re hand candy, as well - Weight: 44g

- Replacement Cassette body for Origin8 hubs

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Authentic replacement freehub for Ritchey V2 Apex and Zeta Phantom Flange road wheels. - For 17mm axle - SRAM XDR

Tubeless setup should be a "set it and forget it" affair. SPANK's tubeless valves are constructed of durable brass material and a tapered round rubber base which fits a wide range of rim designs. The extra-long shafts accommodate even the deepest well rims and most troublesome of pumps. Sealed removable valve cores for sealant injection make set up or topping up a breeze. - Material: Brass shaft, rubber plug - Weight (g): ±18/set - Length (mm): 40 shaft (55 total length) - Features: 2 pcs per set, removable valve core for sealant injection

Lightweight and easy to install, there are Ritchey rim strips for all wheel sizes and types. - Easily snaps over your rims - Stretchy, tightly woven material provides a close fit and protects from abrasion - Sold as a pair - Not for tubeless set up

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer the highest quality, simple, lightweight alternative to that bulky handle. - This axle is compatible with bikes that have a Focus R.A.T. thru-axle in the fork with 100 x 12mm front hubs. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.

Adapts HEX 32 J-Type Front Hubs to 15x100. Compatible with: - HEX J-Type 32H Boost and non-Boost Front Wheels - Also compatible as replacement 15x110 adapters for HEX 32 J-Type Boost Front Hubs. Not compatible with: - HEX 28 Straightpull or HEX Gravel Front Hubs - HEX Straightpull or Gravel Front Wheels. (see HEX 28 front hub adapters) - SPIKE/OOZY/SPOON hubs

Designed to be stiff and durable enough to meet the demands of modern mountain bike riding, the Ritchey WCS BOOST fork thru-axle offers confidence and control for whatever kind of trails you're into. - Type: thru-axle - Material: 7075 Alloy - Axle Length: 135mm - Diameter: 15mm - Thread diameter: M15 - Thread pitch: 1.2mm - Head: hex 6mm - Weight: 63g - Color: black

Replacement Alloy Freehub Body, with Anti-Bite Technology, for all HEX Rear Hubs. Includes spacer ring to also allow the use of MTB cassettes. Compatible with: - All HEX J-Type, Straightpull, and Gravel rear wheels Not compatible with: - SPIKE/OOZY/SPOON hubs

Authentic replacement freehub body for Ritchey Comp and Classic Zeta wheels. - Available for: SRAM XDR

Grade 10 chromium steel balls

Purchase our Kid Trailer axle for your bike, and share your stoke for cycling with your kids. Simplify your life by allowing quick and secure attachment of your trailer to your best and favorite bike. Enjoy the adventure. Robert Axles for Kid Trailers are designed specifically to fit your 12mm thru-axle bike and allow attachment of any hitch-mounted trailer. These fit any trailer that has two wheels and a single point of attachment to the axle. This includes all the two-wheeled child, pet, and cargo trailers such as Thule, Chariot, Burley, Instep, Carry Freedom, and many more. - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The stainless steel axle end allows for mounting of the hitch provided with your trailer. - Hardware for attachment of the hitch is included; the hitch, itself, is not. - No special tools required. Design allows for wheel installation and removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

The same spoke thread treatment used by Stan's pro wheel builders is now available to everyone. Stan's SRD Spoke Powder fills the threads of the spoke and functions as both a lubricant during assembly and a thread lock once built. Each bottle contains 24g (.8oz) which will treat approximately 300 wheels. The PTFE powder in Stan's SRD Spoke Powder acts as a barrier, keeping the metal of the nipple from bonding to the metal of the spoke and preventing spoke wind up during build or adjustment. In promoting a smoother turning nipple, the powder also ensures more accurate and consistent wheel builds, with less “ping and pop" during and after the build. The powder also fills the threads of the spoke to act as a thread lock that prevents loosening and de-tensioning and is particularly well suited for mechanically locking nipples such as Sapim's Secure Lock. - Improves tension consistency and overall build quality - Prevents spoke wind up - Offers secure thread lock between spoke and nipple - Prevents corrosion between spoke and nipple - Can be used dry or as a slurry - Works great with mechanically locking nipples

- Axle adapters for RD-1110 Elite Series rear road disc hubs - Available in standard QR and 12mm thru-axle options - Axles included with adapters

- Axle adapters for FB-1110 Elite Series rear fat bike hubs - Available in standard QR and 12mm thru-axle options, and for 170/190mm and 177/197mm OLD spacing - Material: Aly - Color: Blk

Replacement Alloy XDR (XD-Road) Freehub Body, for all HEX Rear Hubs. Includes spacer ring to also allow the use of MTB cassettes. Compatible with: - All HEX J-Type, Straightpull, and Gravel rear wheels Not compatible with: - SPIKE/OOZY/SPOON hubs

Heavy duty and extra wide PVC rim strips for maximum tube protection.

- Axle adapters for CX/GX/MT/FB-1110 Elite Series front hubs - Available in standard QR, 12mm, 15mm, and 20mm thru-axle options - Material: Aly - Color: Blk

Shimano Nexus and Alfine Internally Geared Hub Cassette Joints - Shimano model # CJ-S700 - Does not include cable fixing bolt unit - OEM cassette joint unit for Alfine SG-S700