Upgrades the DT-5 to the DT-5.2. - Four telescoping axle adaptors - Two stand off studs for Flat Mount alignment - 12mm front fork thru axle sleeve
$116.95 - $173.95
Park Tool offers premium-quality reamers for nearly any bicycle standard. The reamers below are designed to quickly, accurately, and precisely ream headtubes when used with Park's Head Tube Reamer (HTR), ensuring a perfect headset fit and prfoessional-quality bicycle build. Choose the correct reamer for your application using the following information: - 751.2: This reamer is sized to 30.1mm. This allows a 0.1mm interference fit when pressing the 30.2mm headset of the “Euro” one-inch standard. - 754.2: This reamer is sized to 33.9mm. The allows a 0.1mm interference fit when pressing the 34.0mm headset of the 1-1/8" standard. - 788: This reamer is sized to 43.95mm. It reams head tubes to accept “internal” headset cups with 44.05 - 44.10mm O.D. (1-1/8 ZS standard). It is used with Park Tool's 690-XL Facing Cutter and 750 Centering Cone. - 738: This reamer is sized to 52.1mm. It is used to ream head tubes using the 1-1/2" integrated headset standard. It is used with Park Tool's 690-XL Facing Cutter and 750.2 Centering Cone Adapter. - 789: This reamer is sized to 55.95mm. It is used to ream head tubes to accept “internal” headset cups with 56.00–56.10mm O.D. (1-1/2 ZS standard). It is used with Park Tool's 690-XXL Facing Cutter and #750 Centering Cone Adaptor. - 799: This reamer is sized to 47mm. It is used for cutting the lower head tube on frames using an IS47 bearing for a 1-1/4" integrated headset. It cuts a 45-degree bearing set shoulder.
Park's Dial Indicator Gauge Set mounts to their TS-2 or TS-2.2 Truing Stand (sold separately). The set makes it easy to view and correct a wheel's lateral and radial run-out within a tolerance of .01mm. Compared to going by the gap between the truing stand pointer and rim, having gauges that put a number on the clearance makes wheel truing easier and more accurate.
- Used to ream and face BB86/92 bottom bracket shells to an ID of 40.98mm - Used in conjunction with HTR-1 head tube reaming and facing set (PK-6710), 750.2 centering cone adapter (PK-6735) and 690-XL facing cutter (PK-6730)
Park's Big Clicker Torque Wrench is a 15-inch long, 3/8-inch drive ratcheting, click-type torque wrench that provides accurate torque so you can always tighten your components correctly and ensure they stay tight, and prevent damage too. You simply twist the end of the handle to preset your desired torque setting (shown on the handle's built-in gauge) in .02 Newton Meter (Nm) increments. The Big Clicker has a 10 to 60Nm range (88 to 530 inch pounds) and it even comes with its own protective case.
The 37-piece SBS-3 from Park Tool is a comprehensive, shop-quality set of sockets, hex bits, and Torx compatible drivers selected specifically to tackle a wide variety of common bike repair needs. The SBS-3 also includes flat-faced sockets in common sizes for work on suspension forks. Ideal for use with Park Tool torque wrenches, the 3/8" drive bits and sockets are forged from tough, chrome vanadium steel and nickel chrome plated for lasting durability.
With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The TW-6.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). Designed for higher torque settings for repairs and installation in the bottom bracket, cassette lockring and other areas that use a higher torque settings. For lower torque setting, see the TW-5. Comes with its own protective case. - 10–60 Newton meter range (88–530 Inch Pounds) - Adjustable in 0.25 Nm increments - Ratcheting 3/8" drive - Reads and registers for both left hand and right hand threading - Dial-adjust system allows desired torque setting to be preset - Calibrated to be accurate to +/- 4% - Length: 36.2cm (14.25")
World-famous Park Tool quality wrapped up in a great set of metric combination wrenches. The MWR-SET includes 6mm to 17mm wrenches with a 12-point two-way ratcheting box end. Forged from chrome vanadium steel, chrome-plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip. Strong, comfortable, and beautiful! - Includes 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, and 17mm wrenches
A great way to start a tool collection! The perfect combination of tools to help the novice home mechanic clean, adjust, maintain, and do some basic repairs on their bike. The SK-3 includes more than 15 genuine Park Tool products plus a custom Park Tool toolbox. The SK-3 includes: AWS-11 Fold-Up Hex Wrench Set CC-3.2 Chain Checker CN-10 Professional Cable and Housing Cutter CT-5 Mini ChainBrute Chain Tool GP-2 Pre-Glued Super Patch Kit GSC-1 GearClean Brush MLP-1.2 Master Link Pliers PW-5 Pedal Wrench SD-2 Shop Screwdriver: #2 Phillips SW-7.2 Triple Spoke Wrench TL-1.2 Tire Lever Set #1622 Torx Compatible "L" Wrench
Improperly aligned frame or fork dropouts can cause bent axles and quick-release skewers, as well as tracking and shifting problems. The Frame and Fork End Alignment Gauge Set quickly determines whether the frame or fork dropouts are aligned and parallel. If an error is detected, long handles and comfortable molded grips afford plenty of leverage for straightening. These Park gauges adjust to compensate for various hub widths from 100mm to 160mm, too.
With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The Park Tool TW-5.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). With a range of 2-14Nm, the TW-5.2 is designed for the lower torque settings that a shop or consumer would use for proper seat post, seat clamp and handlebar / stem applications. Comes with its own protective case.
This handy tool will save time and frustration! Quickly and accurately cuts hydraulic brake line then precisely installs hose barbs into the tubing when the brake line is either on or off the bike. - Cuts hydraulic brake hose (does not cut steel braided hydraulic hose) - Installs press-in style barbed hose inserts - Replaceable parts including push pin tip and stainless steel blade - Hard anodized body for improved tool wear - Lightweight, CNC machined aluminum body Replacement parts: - 2494K Cutting Blade (set of 2) - 2497 Push Pin Tip
For the mechanic on the go, Park's Backpack Harness carries your Blue Box Tool Case full of tools easily and comfortably. It's complete with padded shoulder, chest and waist straps and extra accessory pouches. The BXB-2 is fully adjustable and set up is quick and easy.
No more need to hold wheels between your knees, balance on a bench top or ask for help. The WH-1 Wheel Holder firmly holds thru axle and quick release wheels at three convenient positions. It’s like having a strong helper to hold wheels during cleaning, tire and tube work, hub work, cassette work, and tubeless installation. The WH-1 can be bolted or clamped directly to a bench or installed in a bench vise. Uses and Features: - Quick and easy access to hold virtually any wheel to perfectly position your work for a variety of tasks including but not limited to: - Wheel building -Cassette removal and installation - Tire and tube removal and installation - Tubeless tire work - General cleaning - Hub work - Holds wheel at vertical, 35 degrees from vertical, and horizontal positions - Accepts 12, 15, and 20mm thru axles and 5mm skewers - E-Nickel finish for durability
A complete tool set to work on both Campagnolo and Fulcrum Ultra-Torque and Power Torque crank and bottom bracket systems (each sold separately). The CBP-8 includes a beefed-up bearing and crank puller and all the fittings necessary to remove and install both systems. - Bearing Puller That Fits Both Power Torque And Ultra-Torque - Crank Puller For Power Torque - Bearing Setter For Both Power Torque And Ultra-Torque - Removal Adaptor For Power Torque Crank Bearings - Removal Protection Pads For Use With Carbon Cranks - Removal Protection Adaptor For Use With Aluminum Crank Arms - Crank Removal Extension Plug For Power Torque
The CRS-15.2 uses two different insert rings to install bearing races on the 1.5-inch and 1-1/4-inch forks. The bearing surface is spared a direct hit by using aluminum inserts. Using a hammer, tap firmly on the end cap of the tube and seat the race into its proper place safely and accurately. Included extension allows work on fork steering tubes up to 425mm. - SHIS terminology: The CRS-15 services crown races in SHIS 33 and 40.
A daily-use, shop version of Park Tool's world-famous CM-5.2 Chain Scrubber. The CM-25 features a super-tough die-cast aluminum case and handle, plus a unique brush/sponge replacement cartridge that makes it easy to keep it running smoothly and working properly. Park Tool's proven four-sided scrubbing action makes thoroughly cleaning chains quick and easy. A shop quality cleaner built to give years of constant use. - Proven chain scrubbing technology leaves chains sparkling clean - Durable A380 aluminum die cast case and removable handle - Dual-sided sponges and wicking pads to help reduce drips - Rotating brushes clean on all four sides of every link - Brush and sponge cartridge quickly and easily clicks in and out (RBS-25) - Locking cover with stainless steel hinge pins - Choose drip or immersion fluid application methods - 100% serviceable
Park Tool's Frame and Fork Straightener is a versatile and productive tool. Its open hook design enables it to straighten not only frames and forks, but also cranks and handlebars and it features vinyl coating on the hook and fulcrum pad to protect painted surfaces. The FFS-2's hook offers 8 inches of fore-aft adjustment and can fit a frame or fork tube of up to 1-3/4 inches in diameter.
Designed and built with the specific needs of the bike mechanic in mind. The RP-SET.2 includes five professional quality pliers for internal snap rings and one for external snap rings. Pliers are made from forged, heat treated cro-moly steel with a return spring and vinyl dipped grips. RP-1: .9mm straight internal. Opens from 22mm down to 0 (tips touching) RP-2: 1.3mm bent internal. Opens from 22mm down to 2mm (center to center) RP-3: 1.3mm bent external. Opens from 2mm (center to center) up to 18mm RP-4: 1.7mm bent internal. Opens from 21mm down to 2mm (center to center) RP-5: 1.7mm straight internal; Opens from 25mm down to 0 (tips touching)
Designed and built with the specific needs of the bike mechanic in mind, the RP-SET features three forged pliers made for internal snap rings and one for external snap rings. Includes: • RP-1: .9mm straight internal. Opens from 22mm down to 0 (tips touching) • RP-2: 1.3mm bent internal. Opens from 22mm down to 2mm (center to center) • RP-3: 1.3mm bent external. Opens from 2mm (center to center) up to 18mm • RP-4: 1.7mm bent internal. Opens from 21mm down to 2mm (center to center)
$29.95 - $86.95
Frame and Fork Taps will become a lifesaver at some time for virtually every mechanic. These taps are made of high-carbon steel and are precision ground. Park Tool Frame and Fork Taps cut easily and fit conventional tap handles.
Quickly, safely and easily set your crown race with Park's CRS-1 Crown Race Setting System. It includes 6 different inserts (3 for 1-inch and 3 for 1-1/8-inch steerer tubes) that ensure full contact with the crown race for precision installation.
Quickly, safely and easily set your crown race on 1.5-inch steerer tubes with Park's CRS-15 Crown Race Setting System. Specifically engineered for oversized steerers, the CRS-15 comes with one setting tube and a 1.5-inch inset that ensures full contact with the crown race for precision installation.
The key to wheels that are strong and reliable is having spokes that are properly and uniformly tensioned. Park's Spoke Tension Meter accurately and reliably measures the absolute tension of each of the spokes in a wheel, as well as the relative tension between all the spokes in a wheel. It's easy to use, affordable and it works on nearly any bicycle spoke, no matter its diameter, material or shape.
The DAG-2.2 is an indispensable shop tool that can be used to both measure and straighten misaligned derailleur hangers solving a high percentage of shifting problems. - Gauge bar made of heavy gauge, chrome plated steel - Adjusts to fit 20" to 29"+ wheels - Replaceable threaded tip - Upgraded large inner shaft for added strength* - Tighter tolerances for improved accuracy* - Improved clearance and reach to fit more frame/hanger combos including low clearance thru-axle derailleur hangers* *Compared to DAG-2
Simple and economical, Park's Home Mechanic Bearing Cup Press is the perfect addition to your toolbox. With a few quick twists it easily installs all sizes of headset cups and one-piece bottom bracket cups.
Never be left looking for an errant wrench when you have Park's Metric Wrench Set. It includes 12 high quality Park metric wrenches from 6 to 17mm in diameter, featuring both box and open ends. They are all forged from chrome vanadium steel, then chrome plated for durability and dipped in Park Tool blue vinyl for outstanding comfort and ease of use.
Park Tool's Centering Gauge represents a dished rear wheel to assist in centering the TS-2.2 or TS-2 truing stands (each sold separately).
Engineered for fit, function, and leverage, these L-shaped shop-quality hex wrenches are a must have for every workshop. - High-torque, industrial steel wrenches - Straight hex shaft on the short side, ball end on the long side - Includes 2, 2.5, 3, 4, 5, 6, 8, and 10mm - Comfortable, ergonomically designed nylon handles fit perfectly in your hand - Durable wall/pegboard mount tool holder allows easy access and organization
Park Shop Cone Wrenches are made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on hubs and other bearing assemblies. Their special Y-heads put more material where it's needed for greater strength. Most applications require several cone wrenches, so Park gives you a whole set, featuring 13mm - 24mm, 26mm and 28mm wrenches to suit your repair needs.