Parts

Take away the suspension rail design, and you get our SAGMA Lite saddle, the more traditional looking option in our line-up, featuring standard CrMo rails. At a lower pice point than our top models, the comfortable idbeads foam technology, the PU-Skin, and the carbon-reinforced extra short saddle shell still remain. - idbeads foam technology with low speed rebound properties - PU-Skin covering - Carbon reinforced shell - CroMo/Steel rails (7x7mm) - Width x length: 142mm x 242mm - 225g

Valve-extension-adapter. Allows easier access to your dropper valve for shock-pumps with short valve heads.

These super tough axles are constructed to Fox's exact specifications and made from 7075 Aluminium. Unlike any other fork axles on the market, these feature a unique double hex design. This includes the traditional 6mm that everyone is familiar with but with an added 8mm Allen key fitting as well. This feature makes removal much easier if the 6mm gets chewed up, over tightened or not removed for a long time. Having an Allen key fitting instead of a QR also allows the use of a torque wrench so you can be sure your wheel is correctly tightened. This Axle also comes with a grade 5 titanium pinch bolt and backing nut to finish things off. Clean, simple, and fast! Replacement for Fox PN: 820-09-071-KIT / Service Set: 2021 36-38 15x110 KaboltX Pinch-axle Assembly 820-09-063-KIT / Service Set: 2020 FOX-Marzocchi 15x110 QR Adjust Axle Assembly NOTE: This axle does not fit 2021+ 32 and 34. (Square Arch)

Bigger, grippier, lighter and as tough as ever. The Penthouse Flat MK5 pedal is here! After two years of development and testing the MK5 Penthouse Flat is here. Retaining our signature toughness, the MK5 is the lightest and grippiest Burgtec pedal to date. We did this by not only increasing the size of the pedal platform but also how concave it is. Furthermore, we reduced the diameter of the pins and added the most wear-resistant internals on the market. From the outside to the inside, we've sweated the details of the MK5 to bring you the ultimate flat pedal. - Weight: 379g - Platform material: 7075 Alloy - Profile: 15mm - Platform: 100mm x 102mm - Dish: 2mm (concave) - Pin material: Stainless steel - Pin width: 3.5mm - Pin height: 4.5mm - Axle Material: EN24T Steel - Internals: 2 x Igus W300 bushings, single sealed bearing and inboard rubber oil seal

When you've got to finish your bike off right. The Burgtec Stem Spacers are the perfect finishing kit.

"Make a grip with the fussiest rider on the planet, you must be mad!!" The Bartender Pro is the next level in grip design for Burgtec. We've collaborated with 3x World Champion Greg Minnaar to hone the construction of this grip to produce unrivaled vibration dampening. - 31.5mm Diameter. - 30A Rubber Compound - Single Lock On

The Goats Grip just went Super Soft. Prototyped through the 2020 season and based on the World Cup Winning pattern of the Bartender Pro as used by Greg, as well as Nina Hoffman, Danny Hart and Angel Suarez. - Super Soft Compound - 31.5mm Diameter - Single Lock-on - Tapered Core

- Complete shifter and brake cables and housing kit - Low friction, prelubricated casing - Cable Material: Stainless Steel - Cables & Housing: Comp.Campagnolo Ergopower Ultra-Shift

PEMBREE DBN is an entirely new seat post clamp. Due to the double barrel nuts DBN provides a consistent clamping force ensuring the bolt remains straight through-out its travel. This is particularly important when clamping dropper posts to prevent pitch points that damage frames and posts. Machined to exacting standards ensures a precision fit that is critical to secure clamping. DBN seat post clamp is manufactured from aluminium that is 75% recycled, unheard of in the industry. Machined from stainless steel the precision, custom made bolt provides the core clamping function of DBN. - Clamp: Aluminium - Bolt: Stainless Steel TX25 - Barrel Nuts: Aluminium - Weight: 27g - Warranty: 5 Years

- Comfort in an affordable first-class saddle. - Padded with Slow Fit Foam, a memory foam that molds to rider's body. - The foam matrix open cell structure confers increased elasticity and breathability to guarantee a durable and comfortable saddle - Integrated Clip System (ICS)

Sun Race, FCM300, Crankset, 48/38/28T, 170mm

These bearing cups are suited for installation of the THM Clavicula on frames with bottom bracket housings to BB30 standard applicable to axles with 30 mm diameter. The bottom bracket housing is 68 mm wide and its inner diameter is 42 mm. The snap rings wich for the BB30 standard are used as limit stop when pressing in the bearings, must not be installed. The relatively small bearing clearance of 68 mm could lead to considerable axle deformations. Our solution with bearings at the outside involves a reduced load on the axle which can be seen from the higher rigidity. Another advantage is the facility of using the same crank for frames to BB30 standard and those with BSA or Italian thread. The increase in weight of the complete system is neglegible. Increase in weight: Road 12 g only

The “Clavicula DH” is the downhill version of our superlight racing crankset. Designed with additional reinforcements it is intended for the extreme demands of downhill racing: Even flying debris, crashes on rocky terrain or sliding along the ground can hardly hurt this crank. Thanks to intelligent design it is still light as a feather. The low weight of the “Clavicula DH” improves the overall handling of any DH bike. A lighter bike will always be more responsive to steering input and thus easier to control. At only 450 g for the complete crankset including the bottom bracket the “Clavicula DH” is much lighter than similar sets. Power transfer and longetivity satisfy the most demanding racer. The crank comes complete with a 38-tooth chainring and is shipped with bottom bracket and mounting tool.

Wolf Tooth headsets are machined here in our Minnesota shop with aircraft-grade 6061 aluminum. They are designed to be lightweight, strong, and durable. Our headsets have three levels of industry-leading custom sealing to protect bearings from the elements and prolong the life of the headset. Available in a variety of colors. These ZS headsets are for frames with internal bearing cups that are pressed into the frame. Premium Headsets with Enduro stainless steel bearings have a lifetime warranty. Upper assembly features: - Ultralight stem cap with integrated spacer plus an aluminum bolt and a star nut. - 6, 15, and 25 mm stack height top cover options (6mm cover = 6mm total stack, 15mm cover = 15 total stack, 25mm cover = 25mm total stack). - O-ring seal prevents water intrusion around the steerer tube. - Custom-molded upper lip seal provides additional protection for the upper bearing.

Parts for repair and maintenance of DT Swiss hubs. - DT Swiss 240s Shim Ring

Parts for repair and maintenance of DT Swiss hubs. - DT Swiss Shim Ring: for Star Ratchet Hubs with 26mm OD Driveside Bearings

RaceFace Crank Arm Fixing Bolts - M15

- Non-SIS 5mm alloy ferrules - Sold individually - Color: Silver

- Aheadset preload adjusting bolt

Replacement small parts for Hope disc brake Hope disc brake calipers.

Hope Brake Lever Parts

Internally fitting service parts for Hayes hydraulic disc brake master cylinders. - All HFX-MAG compatible master cylinder internals are designed for the current aluminum piston/2mm push-rod platform (2003 and newer).

Origin-8's 1 1/8-inch Headset Spacers are made of lightweight and durable aluminum and come in 2mm, 5mm or 10mm thicknesses and lots of cool colors to add style to your ride. You get a bag of 10 spacers.

- Brass barrel, 2.2mm cable pass-through, screwdriver slot on both ends

Shim spacers can be placed between bearing and compression cover in IS headsets to fine tune the fitment.

Service parts for Fox suspension.

Looking to get a little extra distance so that your derailleur clears your 40 or 42 tooth cog? Look no further. - M4 x 24mm screw for that extra little push

Bleed fittings specifically designed for Hayes hydraulic disc brakes.

- Allows quick chain removal without tools - MissingLink 410HD|~|1sp|~|BMX Heavy Duty chain|~|9.4mm|~|each|~| - MissingLink 410|~|1sp|~|BMX|~|8.6mm|~|each|~| - MissingLink II|~|8sp|~|all|~|7.1mm|~|6/card|~| - MissingLink-9|~|9sp|~|all|~|6.6mm|~|6/card|~| - MissingLink-10R|~|10sp|~|KMC, Shimano, SRAM|~|5.9mm|~|6/card|~| - MissingLink-10CR|~|10sp|~|Campagnolo only|~|5.9mm|~|6/card|~| - MissingLink-11|~|11sp|~|Campy, KMC, Shimano|~|5.5mm|~|6/card|~|

Sunlite's Cable End Button replaces the worn out piece that goes between your brake cable and the brake lever body. Replacing it along with cables and housing helps add new life to your brakes and shines u the bike, too!